Распаковка и разборка CPE KuWfi

Discussion in 'Беспроводные технологии/Wi-Fi/Wardriving' started by Triton_Mgn, 7 Mar 2017.

  1. romaaa81

    romaaa81 New Member

    Joined:
    6 Apr 2019
    Messages:
    42
    Likes Received:
    0
    Reputations:
    0
    Здравствуйте , у вас как я вижу сре150 или 830? Если сре150 пожалуйста скажите как вы поставили openwrt и как у вас получилось прошить через putty uart у меня как и у вас в терминале putty каляки были и не реагировала ни на какую клавишу какую скорость выставляли ?
     
  2. Anomaly

    Anomaly Member

    Joined:
    3 May 2018
    Messages:
    44
    Likes Received:
    9
    Reputations:
    0
    Пробуй скорость 118000,помоему она если нет то пробуй эти 111000 108000
     
  3. Den333

    Den333 New Member

    Joined:
    30 May 2019
    Messages:
    1
    Likes Received:
    0
    Reputations:
    0
    Здравствуйте. Имею линк между двумя CPE150 на расстоянии 1,6 км. Одна точка работает в режиме точки доступа, другая в режиме репитера. Спидтест показывает 30мбит на скачивание и 10 мбит на отдачу со стороны репитера. Так вот линк работает стабильно до тех пор пока нагрузка небольшая. Стоит только нагрузить линк по максимуму на некоторое время, как тут же скорость линка падает до 200-300кбит. Захожу удаленно на точку, которая работает в режиме точки доступа при этом веб интерфейс открывается очень медленно, перезагружаю ее, и скорость линка восстанавливается. И так происходит регулярно. На обоих точках стояла прошивка 2.2., решил попробовать поменять прошивку. Поставил 5.0 на точку, которая работает в режиме точки доступа при этом проблема не пропала. Затем и на репитер поставил прошивку 5.0, при этой комбинации прошивок скорость на скачивание осталась прежней около 30мбит, но скорость отдачи упала с 10мбит до 100-200кбит. В итоге на репитере вернул обратно прошивку 2.2. Скорость отдачи вернулась к прежним показателям. В итоге не пойму,что происходит с точкой доступа, почему падает скорость скачивания.
     
  4. freee

    freee Active Member

    Joined:
    8 Aug 2015
    Messages:
    212
    Likes Received:
    227
    Reputations:
    4
    А в режиме моста скорость падает? На рипере есть возможность кабелем подцепиться?
    Попробуйте по ssh подключиться и поиграться с настройками безпровода в ручном режиме. Канал\\Регион\\Мощность\\и тд
    И не смотрите вы на цифры в роутере, проверяйте скорость фактического соединения, тем более он в режиме ТочкиДос. настроен, помехи от соседей\\клиентов могут быть и он с нагрузкой не справляется.
    Единственное не понятно, почему он не восстанавливает скорость после просадки, мб в драйвере трабла.
     
    Af5G4337 and Triton_Mgn like this.
  5. erwerr2321

    erwerr2321 Elder - Старейшина

    Joined:
    19 Jun 2015
    Messages:
    4,032
    Likes Received:
    24,788
    Reputations:
    137
    Ну тут, блин, всё в лучших традициях Античата, сам чёрт ногу сломит!
    Половину темы обсуждали всё что угодно, но не то шо надо! Обожаю! :D
    Пока найдёшь, то что нужно, либо со смеху лопнешь, либо нервный тик заработаешь! :D
    Отпишите, кто-нить в ЛС. Нужна консультация по сабжу.
    Спасибо!
     
  6. romaaa81

    romaaa81 New Member

    Joined:
    6 Apr 2019
    Messages:
    42
    Likes Received:
    0
    Reputations:
    0
    Уважаемыи ANOMALY прошу вас рассказать как вы проживали прогромматором через uart ,какой инструкцией пользовались ,какими командами пользовались при прошивке (загрузчика ; осн. прошивки ; и дампа) у меня тоже сре150 . Инструкцией что здесь не получалось прошивать ,пожалуйста опишите
     
  7. romaaa81

    romaaa81 New Member

    Joined:
    6 Apr 2019
    Messages:
    42
    Likes Received:
    0
    Reputations:
    0
    Пользователи сре150 , кто из вас испробовал новую текстовую прошивку от free выложенные на Гугл диске в папке TEST???
     
  8. romaaa81

    romaaa81 New Member

    Joined:
    6 Apr 2019
    Messages:
    42
    Likes Received:
    0
    Reputations:
    0
    У кого есть сре 150 очень прошу позвоните тестеро куда идет первая ножка от флеш памяти . От того что часто отпаявал и задавала дорожка от первой ножки оборвалась и теперь надо узнать куда идет эта ножка , возможно и в сре 830 такая же распиновка очень прошу
     
  9. saimonyz

    saimonyz Member

    Joined:
    23 Jun 2012
    Messages:
    155
    Likes Received:
    41
    Reputations:
    2
  10. freee

    freee Active Member

    Joined:
    8 Aug 2015
    Messages:
    212
    Likes Received:
    227
    Reputations:
    4
    saimonyz likes this.
  11. saimonyz

    saimonyz Member

    Joined:
    23 Jun 2012
    Messages:
    155
    Likes Received:
    41
    Reputations:
    2
    #951 saimonyz, 4 Jul 2019
    Last edited: 4 Jul 2019
  12. freee

    freee Active Member

    Joined:
    8 Aug 2015
    Messages:
    212
    Likes Received:
    227
    Reputations:
    4
    #952 freee, 4 Jul 2019
    Last edited: 5 Jul 2019
    saimonyz likes this.
  13. saimonyz

    saimonyz Member

    Joined:
    23 Jun 2012
    Messages:
    155
    Likes Received:
    41
    Reputations:
    2
    freee

    прошил 0__18.06.4__( 5.07.2019 )/ramips/mt7621/d-team_newifi-d2-sysupgrade.bin

    тоже самое
    [​IMG]
    [​IMG]

    root@OpenWrt:~# dmesg
    [ 0.000000] Linux version 4.14.131 (ax@ax) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7808-ef686b7292)) #0 SMP Thu Jun 27 12:18:52 2019
    [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
    [ 0.000000] bootconsole [early0] enabled
    [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
    [ 0.000000] MIPS: machine is Newifi-D2
    [ 0.000000] Determined physical RAM map:
    [ 0.000000] memory: 1c000000 @ 00000000 (usable)
    [ 0.000000] memory: 04000000 @ 20000000 (usable)
    [ 0.000000] Initrd not found or empty - disabling initrd
    [ 0.000000] VPE topology {2,2} total 4
    [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
    [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
    [ 0.000000] Zone ranges:
    [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
    [ 0.000000] HighMem [mem 0x0000000010000000-0x0000000023ffffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001bffffff]
    [ 0.000000] node 0: [mem 0x0000000020000000-0x0000000023ffffff]
    [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000023ffffff]
    [ 0.000000] On node 0 totalpages: 131072
    [ 0.000000] free_area_init_node: node 0, pgdat 80583de0, node_mem_map 81003000
    [ 0.000000] Normal zone: 512 pages used for memmap
    [ 0.000000] Normal zone: 0 pages reserved
    [ 0.000000] Normal zone: 65536 pages, LIFO batch:15
    [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15
    [ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x4a8 with crng_init=0
    [ 0.000000] percpu: Embedded 14 pages/cpu s26192 r8192 d22960 u57344
    [ 0.000000] pcpu-alloc: s26192 r8192 d22960 u57344 alloc=14*4096
    [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
    [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130560
    [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
    [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    [ 0.000000] Writing ErrCtl register=00004560
    [ 0.000000] Readback ErrCtl register=00004560
    [ 0.000000] Memory: 513016K/524288K available (4434K kernel code, 233K rwdata, 980K rodata, 228K init, 248K bss, 11272K reserved, 0K cma-reserved, 262144K highmem)
    [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Hierarchical RCU implementation.
    [ 0.000000] NR_IRQS: 256
    [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
    [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
    [ 0.000011] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
    [ 0.007829] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
    [ 0.073992] pid_max: default: 32768 minimum: 301
    [ 0.078773] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.085282] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.094254] Hierarchical SRCU implementation.
    [ 0.099462] smp: Bringing up secondary CPUs ...
    [ 7.967799] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
    [ 7.967809] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    [ 7.967822] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
    [ 7.967973] CPU1 revision is: 0001992f (MIPS 1004Kc)
    [ 0.164252] Synchronize counters for CPU 1: done.
    [ 7.688899] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
    [ 7.688908] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    [ 7.688917] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
    [ 7.688993] CPU2 revision is: 0001992f (MIPS 1004Kc)
    [ 0.255535] Synchronize counters for CPU 2: done.
    [ 7.778043] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
    [ 7.778051] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    [ 7.778060] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
    [ 7.778146] CPU3 revision is: 0001992f (MIPS 1004Kc)
    [ 0.340712] Synchronize counters for CPU 3: done.
    [ 0.370577] smp: Brought up 1 node, 4 CPUs
    [ 0.378313] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [ 0.388104] futex hash table entries: 1024 (order: 3, 32768 bytes)
    [ 0.394429] pinctrl core: initialized pinctrl subsystem
    [ 0.400220] NET: Registered protocol family 16
    [ 0.415250] FPU Affinity set after 11720 emulations
    [ 0.416020] pull PCIe RST: RALINK_RSTCTRL = 0
    [ 0.720675] release PCIe RST: RALINK_RSTCTRL = 7000000
    [ 0.725724] ***** Xtal 40MHz *****
    [ 0.729079] release PCIe RST: RALINK_RSTCTRL = 7000000
    [ 0.734176] Port 0 N_FTS = 1b105000
    [ 0.737644] Port 1 N_FTS = 1b105000
    [ 0.741090] Port 2 N_FTS = 1b102800
    [ 1.896113] PCIE2 no card, disable it(RST&CLK)
    [ 1.900473] -> 21007f2
    [ 1.902878] PCIE0 enabled
    [ 1.905467] PCIE1 enabled
    [ 1.908072] PCI host bridge /pcie@1e140000 ranges:
    [ 1.912847] MEM 0x0000000060000000..0x000000006fffffff
    [ 1.918000] IO 0x000000001e160000..0x000000001e16ffff
    [ 1.923205] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
    [ 1.939020] mt7621_gpio 1e000600.gpio: registering 32 gpios
    [ 1.944856] mt7621_gpio 1e000600.gpio: registering 32 gpios
    [ 1.950605] mt7621_gpio 1e000600.gpio: registering 32 gpios
    [ 1.957664] PCI host bridge to bus 0000:00
    [ 1.961701] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
    [ 1.968559] pci_bus 0000:00: root bus resource [io 0xffffffff]
    [ 1.974385] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
    [ 1.981143] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
    [ 1.989039] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
    [ 1.989081] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
    [ 1.989092] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff]
    [ 1.989159] pci 0000:00:00.0: supports D1
    [ 1.989168] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
    [ 1.989443] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
    [ 1.989471] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
    [ 1.989484] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff]
    [ 1.989535] pci 0000:00:01.0: supports D1
    [ 1.989543] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
    [ 1.989959] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
    [ 1.990013] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
    [ 1.990058] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
    [ 1.990151] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
    [ 1.990345] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
    [ 1.990522] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
    [ 1.990570] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
    [ 1.990696] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
    [ 1.990881] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
    [ 1.990901] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
    [ 1.990967] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
    [ 1.997526] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
    [ 2.004392] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
    [ 2.010990] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
    [ 2.017879] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
    [ 2.024627] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
    [ 2.031779] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
    [ 2.038537] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
    [ 2.045270] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
    [ 2.052030] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
    [ 2.059269] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
    [ 2.066446] pci 0000:00:00.0: PCI bridge to [bus 01]
    [ 2.071353] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
    [ 2.078107] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
    [ 2.085273] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
    [ 2.092026] pci 0000:00:01.0: PCI bridge to [bus 02]
    [ 2.096928] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
    [ 2.105083] clocksource: Switched to clocksource GIC
    [ 2.111489] NET: Registered protocol family 2
    [ 2.116562] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
    [ 2.123449] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
    [ 2.129894] TCP: Hash tables configured (established 2048 bind 2048)
    [ 2.136319] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [ 2.142085] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [ 2.148570] NET: Registered protocol family 1
    [ 2.152894] PCI: CLS 0 bytes, default 32
    [ 2.385029] 4 CPUs re-calibrate udelay(lpj = 2924544)
    [ 2.391235] Crashlog allocated RAM at address 0x3f00000
    [ 2.396676] workingset: timestamp_bits=30 max_order=17 bucket_order=0
    [ 2.409503] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [ 2.415282] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
    [ 2.428341] random: fast init done
    [ 2.431783] bounce: pool size: 64 pages
    [ 2.435597] io scheduler noop registered
    [ 2.439423] io scheduler deadline registered (default)
    [ 2.445024] gpio-export gpio_export: 1 gpio(s) exported
    [ 2.451125] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
    [ 2.458954] console [ttyS0] disabled
    [ 2.462505] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
    [ 2.471525] console [ttyS0] enabled
    [ 2.478405] bootconsole [early0] disabled
    [ 2.487016] cacheinfo: Failed to find cpu0 device node
    [ 2.492139] cacheinfo: Unable to detect cache hierarchy for CPU 0
    [ 2.498970] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
    [ 2.506345] spi-mt7621 1e000b00.spi: sys_freq: 50000000
    [ 2.521229] m25p80 spi0.0: w25q256 (32768 Kbytes)
    [ 2.526030] 4 fixed-partitions partitions found on MTD device spi0.0
    [ 2.532352] Creating 4 MTD partitions on "spi0.0":
    [ 2.537146] 0x000000000000-0x000000030000 : "u-boot"
    [ 2.543124] 0x000000030000-0x000000040000 : "u-boot-env"
    [ 2.549435] 0x000000040000-0x000000050000 : "factory"
    [ 2.555485] 0x000000050000-0x000002000000 : "firmware"
    [ 2.661116] 2 uimage-fw partitions found on MTD device firmware
    [ 2.667055] 0x000000050000-0x00000021b778 : "kernel"
    [ 2.672984] 0x00000021b778-0x000002000000 : "rootfs"
    [ 2.678868] mtd: device 5 (rootfs) set to be root filesystem
    [ 2.684663] 1 squashfs-split partitions found on MTD device rootfs
    [ 2.690954] 0x000000610000-0x000002000000 : "rootfs_data"
    [ 2.698396] libphy: Fixed MDIO Bus: probed
    [ 2.767084] libphy: mdio: probed
    [ 4.169986] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
    [ 4.176724] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20
    [ 4.187725] NET: Registered protocol family 10
    [ 4.193804] Segment Routing with IPv6
    [ 4.197634] NET: Registered protocol family 17
    [ 4.202130] 8021q: 802.1Q VLAN Support v1.8
    [ 4.208938] hctosys: unable to open rtc device (rtc0)
    [ 4.220436] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
    [ 4.228052] Freeing unused kernel memory: 228K
    [ 4.232490] This architecture does not have kernel memory protection.
    [ 4.503918] random: crng init done
    [ 4.773503] init: Console is alive
    [ 4.777218] init: - watchdog -
    [ 5.260995] kmodloader: loading kernel modules from /etc/modules-boot.d/*
    [ 5.325771] usbcore: registered new interface driver usbfs
    [ 5.331344] usbcore: registered new interface driver hub
    [ 5.336856] usbcore: registered new device driver usb
    [ 5.352053] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
    [ 5.357447] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
    [ 5.375263] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
    [ 5.384443] xhci-mtk 1e1c0000.xhci: irq 19, io mem 0x1e1c0000
    [ 5.391208] hub 1-0:1.0: USB hub found
    [ 5.395136] hub 1-0:1.0: 2 ports detected
    [ 5.399712] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
    [ 5.405111] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
    [ 5.412580] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
    [ 5.419201] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
    [ 5.428191] hub 2-0:1.0: USB hub found
    [ 5.432021] hub 2-0:1.0: 1 port detected
    [ 5.439388] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
    [ 5.455448] init: - preinit -
    [ 6.240995] mtk_soc_eth 1e100000.ethernet: PPE started
    [ 6.401994] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
    [ 9.536217] jffs2: notice: (448) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 2 orphan) and 2 of xref (2 dead, 0 orphan) found.
    [ 9.553851] mount_root: overlay filesystem has not been fully initialized yet
    [ 9.563997] mount_root: switching to jffs2 overlay
    [ 9.583805] overlayfs: upper fs does not support tmpfile.
    [ 9.592800] urandom-seed: Seed file not found (/etc/urandom.seed)
    [ 9.722043] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
    [ 9.737313] procd: - early -
    [ 9.740303] procd: - watchdog -
    [ 10.385232] procd: - watchdog -
    [ 10.388704] procd: - ubus -
    [ 10.484348] procd: - init -
    [ 10.720913] kmodloader: loading kernel modules from /etc/modules.d/*
    [ 10.731160] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [ 10.746455] ip_tables: (C) 2000-2006 Netfilter Core Team
    [ 10.758721] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
    [ 10.800831] xt_time: kernel timezone is -0000
    [ 10.811369] PPP generic driver version 2.4.2
    [ 10.817040] NET: Registered protocol family 24
    [ 10.824006] kmodloader: done loading kernel modules from /etc/modules.d/*
    [ 19.070322] mtk_soc_eth 1e100000.ethernet: PPE started
    [ 19.084770] br-lan: port 1(eth0.1) entered blocking state
    [ 19.090349] br-lan: port 1(eth0.1) entered disabled state
    [ 19.096408] device eth0.1 entered promiscuous mode
    [ 19.101198] device eth0 entered promiscuous mode
    [ 19.110445] br-lan: port 1(eth0.1) entered blocking state
    [ 19.115926] br-lan: port 1(eth0.1) entered forwarding state
    [ 19.121900] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
    [ 20.075832] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
    root@OpenWrt:~#

    root@OpenWrt:~# iwconfig
    lo no wireless extensions.

    eth0.1 no wireless extensions.

    eth0 no wireless extensions.

    eth0.2 no wireless extensions.

    br-lan no wireless extensions.

    root@OpenWrt:~#

    root@OpenWrt:~# ifconfig
    br-lan Link encap:Ethernet HWaddr 20:76:93:47:89:D3
    inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
    inet6 addr: fe80::2276:93ff:fe47:89d3/64 Scope:Link
    inet6 addr: fd05:d4a8:310e::1/60 Scope:Global
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:2405 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1736 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:189567 (185.1 KiB) TX bytes:509994 (498.0 KiB)

    eth0 Link encap:Ethernet HWaddr 20:76:93:47:89:D3
    inet6 addr: fe80::2276:93ff:fe47:89d3/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:2621 errors:0 dropped:3 overruns:0 frame:0
    TX packets:1890 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:250465 (244.5 KiB) TX bytes:561732 (548.5 KiB)
    Interrupt:20

    eth0.1 Link encap:Ethernet HWaddr 20:76:93:47:89:D3
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:2405 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1736 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:189567 (185.1 KiB) TX bytes:509994 (498.0 KiB)

    eth0.2 Link encap:Ethernet HWaddr 20:76:93:47:89:D4
    inet6 addr: fe80::2276:93ff:fe47:89d4/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:101 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 B) TX bytes:30380 (29.6 KiB)

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:65536 Metric:1
    RX packets:230 errors:0 dropped:0 overruns:0 frame:0
    TX packets:230 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:17108 (16.7 KiB) TX bytes:17108 (16.7 KiB)

    root@OpenWrt:~#

    на CPE830 всё норм
     
    #953 saimonyz, 5 Jul 2019
    Last edited: 5 Jul 2019
  14. freee

    freee Active Member

    Joined:
    8 Aug 2015
    Messages:
    212
    Likes Received:
    227
    Reputations:
    4
    А файл /etc/config/wireless
    Что пишет при вводе wifi

    Эм, а выложите список установленных пакетов
     
    #954 freee, 5 Jul 2019
    Last edited: 5 Jul 2019
  15. saimonyz

    saimonyz Member

    Joined:
    23 Jun 2012
    Messages:
    155
    Likes Received:
    41
    Reputations:
    2
    его вообще нету
    [​IMG]

    в прошивке тоже

    [​IMG]
     
  16. freee

    freee Active Member

    Joined:
    8 Aug 2015
    Messages:
    212
    Likes Received:
    227
    Reputations:
    4
    Все ясно, в сборочных инструкциях не выбраны драйвера wireless ))))
    Очень странно ... будем править)

    Вообще бред какой то, инструкции есть, но автоматом они не ставятся, вернее ставиться только драйвер на usb3
     
    #956 freee, 5 Jul 2019
    Last edited: 5 Jul 2019
    saimonyz likes this.
  17. saimonyz

    saimonyz Member

    Joined:
    23 Jun 2012
    Messages:
    155
    Likes Received:
    41
    Reputations:
    2
    я х3 не разбираюсь , если нужны логи скину
     
  18. freee

    freee Active Member

    Joined:
    8 Aug 2015
    Messages:
    212
    Likes Received:
    227
    Reputations:
    4
    Дубль ТРИ. Пробуйте
     
  19. saimonyz

    saimonyz Member

    Joined:
    23 Jun 2012
    Messages:
    155
    Likes Received:
    41
    Reputations:
    2
    спасибо работает

    Wireless появился сеть сканер ловит, ну в пентесте сканер не работает , монитор мод включается ну опядже нечего не видит
     
    #959 saimonyz, 5 Jul 2019
    Last edited: 5 Jul 2019
  20. freee

    freee Active Member

    Joined:
    8 Aug 2015
    Messages:
    212
    Likes Received:
    227
    Reputations:
    4
    А ротатор выключен?
    Мб траблы с драйвером, попробуйте в ручном режиме через командную строку перевести в монитор моде и отсканировать
     
Loading...
Similar Threads - Распаковка разборка KuWfi
  1. NeXT-123
    Replies:
    0
    Views:
    2,308