Kali Linux на Raspberry Pi 3 с кастомным дисплеем

Discussion in 'Песочница' started by Card3, 27 Apr 2017.

  1. Card3

    Card3 Member

    Joined:
    15 Nov 2008
    Messages:
    29
    Likes Received:
    26
    Reputations:
    1
    Купил я экран ( 800 на 400 ), только вот Kali Linux не видит это ращрешение.

    К экрану китаец приложил описание, в котором есть ссылка на github. Заходишь, скачиваешь драйвер.

    Далее всё просто.

    1. chmod -R 755 LCD-show
    2. cd LCD-show/
    3. ./LCD7B-show
    Но после этого не стартует GUI. Сделал пару тем ( одну на гитхабе, другую на оф. форуме Kali linux )

    Везде тишина. Вся надежда на вас, форумчане.

    Вот сами файлы ( скопированы с github`а для тех, кто не хочет переходить по ссылке выше )


    Code:
    sudo cp -rf ./boot/config-7B-800x480.txt /boot/config.txt
    sudo cp ./usr/cmdline.txt /boot/
    sudo cp ./usr/inittab /etc/
    sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
    sudo reboot

    Code:
    # For more options and information see
    # http://www.raspberrypi.org/documentation/configuration/config-txt.md
    # Some settings may impact device functionality. See link above for details
    
    # uncomment if you get no picture on HDMI for a default "safe" mode
    #hdmi_safe=1
    
    # uncomment this if your display has a black border of unused pixels visible
    # and your display can output without overscan
    #disable_overscan=1
    
    # uncomment the following to adjust overscan. Use positive numbers if console
    # goes off screen, and negative if there is too much border
    #overscan_left=16
    #overscan_right=16
    #overscan_top=16
    #overscan_bottom=16
    
    # uncomment to force a console size. By default it will be display's size minus
    # overscan.
    #framebuffer_width=1280
    #framebuffer_height=720
    
    # uncomment if hdmi display is not detected and composite is being output
    hdmi_force_hotplug=1
    
    # uncomment to force a specific HDMI mode (this will force VGA)
    #hdmi_group=1
    #hdmi_mode=1
    
    # uncomment to force a HDMI mode rather than DVI. This can make audio work in
    # DMT (computer monitor) modes
    #hdmi_drive=2
    
    # uncomment to increase signal to HDMI, if you have interference, blanking, or
    # no display
    #config_hdmi_boost=4
    
    # uncomment for composite PAL
    #sdtv_mode=2
    
    #uncomment to overclock the arm. 700 MHz is the default.
    #arm_freq=800
    
    # Uncomment some or all of these to enable the optional hardware interfaces
    dtparam=i2c_arm=on
    #dtparam=i2s=on
    dtparam=spi=on
    enable_uart=1
    # Uncomment this to enable the lirc-rpi module
    #dtoverlay=lirc-rpi
    
    # Additional overlays and parameters are documented /boot/overlays/README
    
    # Enable audio (loads snd_bcm2835)
    dtparam=audio=on
    max_usb_current=1
    hdmi_drive=1
    hdmi_group=2
    hdmi_mode=1
    hdmi_mode=87
    hdmi_cvt 800 480 60 6 0 0 0
    dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900

    Code:
    dwc_otg.lpm_enable=0 console=tty1 console=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo
    

    Code:
    # /etc/inittab: init(8) configuration.
    # $Id: inittab,v 1.91 2002/01/25 13:35:21 miquels Exp $
    
    # The default runlevel.
    id:2:initdefault:
    
    # Boot-time system configuration/initialization script.
    # This is run first except when booting in emergency (-b) mode.
    si::sysinit:/etc/init.d/rcS
    
    # What to do in single-user mode.
    ~~:S:wait:/sbin/sulogin
    
    # /etc/init.d executes the S and K scripts upon change
    # of runlevel.
    #
    # Runlevel 0 is halt.
    # Runlevel 1 is single-user.
    # Runlevels 2-5 are multi-user.
    # Runlevel 6 is reboot.
    
    l0:0:wait:/etc/init.d/rc 0
    l1:1:wait:/etc/init.d/rc 1
    l2:2:wait:/etc/init.d/rc 2
    l3:3:wait:/etc/init.d/rc 3
    l4:4:wait:/etc/init.d/rc 4
    l5:5:wait:/etc/init.d/rc 5
    l6:6:wait:/etc/init.d/rc 6
    # Normally not reached, but fallthrough in case of emergency.
    z6:6:respawn:/sbin/sulogin
    
    # What to do when CTRL-ALT-DEL is pressed.
    ca:12345:ctrlaltdel:/sbin/shutdown -t1 -a -r now
    
    # Action on special keypress (ALT-UpArrow).
    #kb::kbrequest:/bin/echo "Keyboard Request--edit /etc/inittab to let this work."
    
    # What to do when the power fails/returns.
    pf::powerwait:/etc/init.d/powerfail start
    pn::powerfailnow:/etc/init.d/powerfail now
    po::powerokwait:/etc/init.d/powerfail stop
    
    # /sbin/getty invocations for the runlevels.
    #
    # The "id" field MUST be the same as the last
    # characters of the device (after "tty").
    #
    # Format:
    #  <id>:<runlevels>:<action>:<process>
    #
    # Note that on most Debian systems tty7 is used by the X Window System,
    # so if you want to add more getty's go ahead but skip tty7 if you run X.
    #
    1:2345:respawn:/sbin/getty --noclear 38400 tty1
    2:23:respawn:/sbin/getty 38400 tty2
    3:23:respawn:/sbin/getty 38400 tty3
    4:23:respawn:/sbin/getty 38400 tty4
    5:23:respawn:/sbin/getty 38400 tty5
    6:23:respawn:/sbin/getty 38400 tty6
    
    # Example how to put a getty on a serial line (for a terminal)
    #
    #T0:23:respawn:/sbin/getty -L ttyS0 9600 vt100
    #T1:23:respawn:/sbin/getty -L ttyS1 9600 vt100
    
    # Example how to put a getty on a modem line.
    #
    #T3:23:respawn:/sbin/mgetty -x0 -s 57600 ttyS3
    
    
    #Spawn a getty on Raspberry Pi serial line
    T0:23:respawn:/sbin/getty -L ttyAMA0 115200 vt100
    

    Code:
    # For more options and information see
    # http://www.raspberrypi.org/documentation/configuration/config-txt.md
    # Some settings may impact device functionality. See link above for details
    
    # uncomment if you get no picture on HDMI for a default "safe" mode
    #hdmi_safe=1
    
    # uncomment this if your display has a black border of unused pixels visible
    # and your display can output without overscan
    #disable_overscan=1
    
    # uncomment the following to adjust overscan. Use positive numbers if console
    # goes off screen, and negative if there is too much border
    #overscan_left=16
    #overscan_right=16
    #overscan_top=16
    #overscan_bottom=16
    
    # uncomment to force a console size. By default it will be display's size minus
    # overscan.
    #framebuffer_width=1280
    #framebuffer_height=720
    
    # uncomment if hdmi display is not detected and composite is being output
    hdmi_force_hotplug=1
    
    # uncomment to force a specific HDMI mode (this will force VGA)
    #hdmi_group=1
    #hdmi_mode=1
    
    # uncomment to force a HDMI mode rather than DVI. This can make audio work in
    # DMT (computer monitor) modes
    #hdmi_drive=2
    
    # uncomment to increase signal to HDMI, if you have interference, blanking, or
    # no display
    #config_hdmi_boost=4
    
    # uncomment for composite PAL
    #sdtv_mode=2
    
    #uncomment to overclock the arm. 700 MHz is the default.
    #arm_freq=800
    
    # Uncomment some or all of these to enable the optional hardware interfaces
    dtparam=i2c_arm=on
    #dtparam=i2s=on
    dtparam=spi=on
    enable_uart=1
    # Uncomment this to enable the lirc-rpi module
    #dtoverlay=lirc-rpi
    
    # Additional overlays and parameters are documented /boot/overlays/README
    
    # Enable audio (loads snd_bcm2835)
    dtparam=audio=on
    max_usb_current=1
    hdmi_drive=1
    hdmi_group=2
    hdmi_mode=1
    hdmi_mode=87
    hdmi_cvt 800 480 60 6 0 0 0
    dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
    

    -----


    Вопрос. Как запустить GUI на экран?
     
  2. Dr_Wile

    Dr_Wile Member

    Joined:
    19 Oct 2016
    Messages:
    121
    Likes Received:
    52
    Reputations:
    2
    Экран у Вас случайно не XPT2046? Если да то есть одна ссылка https://whitedome.com.au/re4son/sticky-fingers-kali-pi . Я сам не пробовал ставить, ибо подключения по Ethernet к Интернету у меня нет, а через консоль настроить Wi-Fi подключение не смог. Человек с форума говорил, что у него удалось завести этот экран и выводить на него и консоль и графику. Попробуйте и Вы, в случае успеха/провала сообщите мне либо в личку, либо в этом обсуждении если это не составит для Вас труда
     
Loading...